Send Message
Home News

You should know these maintenance measures for long arm excavators (part 1)

Good quality Heavy Duty Excavator Bucket for sales
We tried our first order in 2018, which was two years after I exchange my business card with Alice in 2016 Bauma conexpo India. Our supplier didn't finish our order on time, and it will cause around 100,000 USD lose to us. That's when we tried Huitong the first time. Huitong is good at dealing with rush orders, and the quality is very good.

—— Mr.Varun, Dealer, India

I work with Huitong the first time when I started my importing business. I've got tons of market insights from Jeremy. He is such a good friend being very tolerant to my bad temper. In 2017, Jeremy helped me handle a problem of bill of lading, which is caused by me. Huitong always emphasize that we should deal with the problem as soon as it occurs.

—— Mr.Stanislav Lilov, Bulgaria

We started cooperated with Huitong from 2017, they are honest, professional, always help us slove problems at the first step, we buy excavator attachments from Huitong in one stop, we share market insights like a good friend. Love Their Work.

—— Sony

I'm Online Chat Now
Company News
You should know these maintenance measures for long arm excavators (part 1)
You should know these maintenance measures for long arm excavators (part 1)

1. The engine speed drops

First, test the output power of the engine itself. If the output power of the engine is lower than the rated power, the cause of the failure may be poor fuel quality, low fuel pressure, incorrect valve clearance, a certain cylinder of the engine not working, wrong fuel injection timing, and fuel The setting value of the volume is incorrect, the air intake system is leaking, the brake and its control lever are faulty, and the turbocharger is carbonized. If the output power of the engine is normal, it is necessary to check whether the flow rate of the hydraulic pump does not match the output power of the engine.


long arm excavators


The speed of hydraulic long arm excavators is inversely proportional to load during operation, that is, the product of flow rate and pump output pressure is an invariant, and the output power of the pump is constant or approximately constant. If the pump control system fails, the optimal load matching state of the engine, pump, and valve in different working conditions cannot be realized, and the excavator will not work normally. Such failures should start with the electrical system, then check the hydraulic system, and finally check the mechanical transmission system.


2. Working speed slows down

The main reason for the slower working speed of the long arm excavators is that the engine power is reduced and the hydraulic system leaks due to the wear and tear of the whole machine. The hydraulic pump of the excavator is a variable plunger pump. After working for a certain period of time, the internal hydraulic components of the pump (cylinder block, plunger, valve plate, nine-hole plate, turtle back, etc.) will inevitably produce excessive wear, which will cause internal leakage. The parameter data is not coordinated, resulting in insufficient flow and high oil temperature and slow working speed. At this time, the whole machine needs to be overhauled, and the parts that wear out of the limit are repaired and replaced.


But if it is not for the long arm excavators that has a long working hours to suddenly slow down, you need to check the following aspects. First check whether the circuit fuse is open or short-circuited, then check whether the pilot pressure is normal, then check whether the servo control valve-servo piston is stuck and whether the distributor confluence is faulty, etc., and finally the hydraulic pump is disassembled for data measurement to confirm the problem of the excavator .


long arm excavators


3. Common faults in the process of excavation

Some common faults that often occur in the construction work of long arm excavators, such as: the excavator runs off-track, which may be caused by damage to the walking distribution oil seal (also known as the center rotary joint oil seal); the flow rates of the two hydraulic pumps are different; has a problem. If the hydraulic cylinder drains quickly, it may be that the safety relief valve is not tightly closed, or the oil seal of the cylinder is severely damaged, etc.

Pub Time : 2022-02-21 14:24:48 >> News list
Contact Details
Guangzhou Huitong Machinery Co., Ltd.

Contact Person: Mr. Tang

Tel: 86-18922117251

Send your inquiry directly to us (0 / 3000)